great software i use it daily.
i updated to latest edition and ever since than whenever i try to synchronise comp with the phone my "myexplorer" crashes. i didn't do anything except just click on the shortcut. after that it would sync with phone and on the last item on the sync process it would crash.
my explorer chrashing issue
-
al3m
I have it very similar.
Yesterday I updated from version 1.3.x, which worked well.
After a fresh installation, computer restart, all MPE user data manually scratched - it connected (manually) via BT on comm41, synchronized data without any problem, worked around a minute or two and crashed with MS Windows standard message. This scenario repeated over and over.
Lets go on. After a new start of MPE (after the crash) it tries to connect to a cell phone via last selected com 41 and the process gives up with a popup message "Error,Phone could not be identified."
After that there is a dump from "Debug.txt" - see at the end of this message.
Then, closing the MPE application, deleting both "general.ini" and user's "settings.dat" (deleting only one of them won't help), starting application, manually selecting com 41 and it works again - until it either gives up with a popup message or crashes.
As I typed above, I use to have no serious problem with the 1.3 version.
Of course I can revert back to 1.3, but I have found this forum, so testing if it works
Ovo
----------------------------------------------------------
EDIT: Finally, I found it less complicated then I described above.
The MPE fails to connect every time the bluetooth connection was disconnected - reconnected from the last MPE session.
I have found surprising workaround. When MPE fails to connect, I open F2-Options and click Search for devices. The search fails to find connection. I close the Options, press F1 twice (disconnect/connect) and surprise!!! It connects the the cell phone.
-----------------------------------------------------------
Yesterday I updated from version 1.3.x, which worked well.
After a fresh installation, computer restart, all MPE user data manually scratched - it connected (manually) via BT on comm41, synchronized data without any problem, worked around a minute or two and crashed with MS Windows standard message. This scenario repeated over and over.
Lets go on. After a new start of MPE (after the crash) it tries to connect to a cell phone via last selected com 41 and the process gives up with a popup message "Error,Phone could not be identified."
After that there is a dump from "Debug.txt" - see at the end of this message.
Then, closing the MPE application, deleting both "general.ini" and user's "settings.dat" (deleting only one of them won't help), starting application, manually selecting com 41 and it works again - until it either gives up with a popup message or crashes.
As I typed above, I use to have no serious problem with the 1.3 version.
Of course I can revert back to 1.3, but I have found this forum, so testing if it works
Ovo
----------------------------------------------------------
EDIT: Finally, I found it less complicated then I described above.
The MPE fails to connect every time the bluetooth connection was disconnected - reconnected from the last MPE session.
I have found surprising workaround. When MPE fails to connect, I open F2-Options and click Search for devices. The search fails to find connection. I close the Options, press F1 twice (disconnect/connect) and surprise!!! It connects the the cell phone.
-----------------------------------------------------------
Code: Alles auswählen
Logdatei MyPhoneExplorer
************************
Programmversion: 1.5.9
Datum: 2/27/2007
14:48:32.63 Setting Port: 41
14:48:32.63 Setting Baud: 115200
14:48:32.63 Avaiable Ports: COM1=\Device\Serial0; COM6=\Device\porte6; COM7=\Device\porte7; COM10=\Device\porte10; COM11=\Device\porte11; COM12=\Device\porte12; COM13=\Device\porte13; COM14=\Device\porte14; COM20=\Device\porte20; COM21=\Device\porte21; COM40=\Device\porte40; COM41=\Device\porte41;
14:48:33.27 Hauptfenster wird geladen
14:48:33.54 Sidebar fertig geladen
14:48:33.57 Farbschema wurde gelesen
14:48:33.62 UC SMS wird geladen
14:48:33.66 UC Phonebook wird geladen
14:48:33.68 UC Phonebook fertig geladen
14:48:33.70 UC Calls wird geladen
14:48:33.74 UC Organizer wird geladen
14:48:33.82 DoItemUpdate
14:48:33.85 DoItemUpdate fertig
14:48:33.90 Cleardetails...
14:48:33.90 Cleardetails fertig
14:48:33.91 UC Notes wird geladen
14:48:33.93 UC Calls wird geladen
14:48:33.98 Avaiable Ports: COM1=\Device\Serial0; COM6=\Device\porte6; COM7=\Device\porte7; COM10=\Device\porte10; COM11=\Device\porte11; COM12=\Device\porte12; COM13=\Device\porte13; COM14=\Device\porte14; COM20=\Device\porte20; COM21=\Device\porte21; COM40=\Device\porte40; COM41=\Device\porte41;
14:48:33.98 Neue COM-Bibliothek wird verwendet
14:48:34.23 Settimeout: RT=2000 WT=200
14:48:34.73 Port 41 wurde geöffnet !
14:48:34.74 [TX]: AT+CGSN
14:48:38.37 Port 41 wird geschlossen
14:48:38.53 Setting Lastuser: Sony Ericsson K750 [352557017847974]
14:48:38.53 Lade Userdatenbank: Sony Ericsson K750 [352557017847974]
14:48:38.53 GMT Einstellungen geladen
14:48:38.53 InfoSMS geladen
14:48:38.53 Notizeintrag gesetzt
14:48:38.86 Kontakte geladen
14:48:38.89 DoItemUpdate
14:48:38.96 DoItemUpdate fertig
14:48:38.98 Organizer geladen
14:48:39.00 Notizen geladen
14:48:39.00 SMS - Datenbank wird geladen...
14:48:39.11 SMS Laden - Readfile: 0 Split: 0 Parse: 110 HandleMultiSMS: 0 Nachrichten: 96
14:48:39.21 SMS geladen
14:48:39.29 Anrufe geladen
14:48:39.48 Hauptfenster fertig geladen
14:48:42.58 Downloader: RC=6 BytesMax=5 BytesTMP=5 URL=http://www.fjsoft.at/myphoneexplorer/version.txt
Zuletzt geändert von Ovo am Di 27. Feb 2007, 17:50, insgesamt 2-mal geändert.
Just found the Toshiba BT issue. I have the 2.1.1127.0 version.
This explains problems with the pop-ups (though it did not explain there was not any with version 1.3).
This explains problems with the pop-ups (though it did not explain there was not any with version 1.3).