FJ Software

I am testing the Compatibility with K610i .. YET i dont see any problems, but maybe cause i just bought that phone ..

Is there anyone tested it already ??

No, up to yet nobody reported me about the K610. Please test all you can find and give feedback so i can add it to the supported phones.

it works with k610. but ill get the k700 pic @ monitor section =)

Cause the K700-pic in monitor. I think there will be bader bugs
The specified phone-picture is only avaiable for the most used modells, cause i want to keep MyPhoneExplorer small.

Well i guess its better if you let people DOWNLOAD the icons wich belongs to thier phones after hand .. i mean as an update for your program ..

FJ hat geschrieben:Cause the K700-pic in monitor. I think there will be bader bugs
The specified phone-picture is only avaiable for the most used modells, cause i want to keep MyPhoneExplorer small.

1. Whenever i send any SMS (With Delivry repport) i dont get no repport at all if the SMS reached or NOT .. i had a W800i earlier and used My Phone Explorer .. it worked fine.. but now with the new K610i is NOT working ..

2. Another bug i am showing in the picture below .. look at number 1 ... the phone picture is K700 not K610i ..

3. The signal quality is 319% !!! i dont think its right ..



4. This alarm signal thingy is not workable ..

About the K610-picture in monitor: I think i said enought
Cause the signal quality i would need your logfile
The alarmtone cannot be set - i know this. Since the K700 series this doesn't work anymore.

Where can i find the LOGfile ??

FJ hat geschrieben:About the K610-picture in monitor: I think i said enought
Cause the signal quality i would need your logfile
The alarmtone cannot be set - i know this. Since the K700 series this doesn't work anymore.

You will find the logfile here

br ...

I sent you the LOG file .. but i just connected the phone without sending SMS .. so i guess i should even SEND SMS so you can see in the log whats going on why the delivry rapport is not showing .. .. i am going to email you very soon ..

FJ hat geschrieben:About the K610-picture in monitor: I think i said enought
Cause the signal quality i would need your logfile
The alarmtone cannot be set - i know this. Since the K700 series this doesn't work anymore.

I sent it now to your E-Mail FJ

About SMS-deliver-bug: Fixed, Sweden 3G send the report in another format as i knew it from the other european providers. Please wait for the next update.

About the signal quality: The phone always replies the line: +CSQ: 99,99
This value is not right, so i think this cannot be fixed.

I dont know what happened !! but i try to send SMS now .. its not working i get error message telling :

+CMS ERROR: 500



Whats wrong with it ??

Shall i send you the log file for today ?? or you know what´s wrong ??

NOW after 10 minutes i try to send SMS its working !!! so why didnt work earlier ??

Again i got problem with it .. i think its better that i send you the LOG file for today to check out what´s wrong .. FJ

Its a normal error depending on your provider. I had the same thing with my lo-cost-provider.

Well .. Swedish TELE2 is not LO-cost provider .. but its ok .. maybe they have some problems right now .. its working again .. thanks

FJ hat geschrieben:Its a normal error depending on your provider. I had the same thing with my lo-cost-provider.

I am having some troubles with my k610i using MyPhoneExplorer...
I installed the SE drivers that came on the CD with my phone. When i plug it in, it comes up in device manager as multiple devices - An OBEX interface on com11, phone manager interface on com12, modem on com10, etc etc.

I can tell myphoneexplorer to use com12, and it connects just fine, and i can read sms messages and see the phone info. However, i can not browse any files, or download contacts.

If i try to tell myphoneexplorer to use com11 (obex interface) for connection, it cant connect (identification failure).

Can someone suggest what I should do? Other people have posted saying that it works for them... any ideas?

Thanks.

Always use one of the two modem-Ports with MyPhoneExplorer. If this doesn't help set your PC-language to english and if needed disable chinese languagesupport.

Ah thanks!
I'll try that when i get home tonight

Thanks for the excellent software!

Hmm, I have tried with the modem interfaces too... I still cannot use the OBEX functions

I also disabled chinese language input - is that what you meant?